IU2MWK
New Member
QUIS ULTRA ?
Posts: 10
|
Post by IU2MWK on Sept 14, 2020 15:44:01 GMT
hi daniel, have a couple of questions, i programmed my radio to the way you had shown was working great on 91 but nothing coming up on my hotspot or dashboard any clues, the other question is fired the radio up this morning press the ptt in and its coming up as bs failed.... BS Failed mean your Repeater or Hotspot is not responding. I had same issue on my Repeater and i try with CDR300 i had BS failed. so i took my mobile and MD380 to try and had same thing long beep that RPT is not available. I have to reboot Pi-Star of the repeater and then it worked. It is like putting a fake Frequency in your channel and result will be the same. HI Daniel,i'm new user from Italy-I understand if i want to work in simplex mode (no repeater) to listen commercial communications the RX slot need to be set to OFF?-It's correct? So i just complete the RX list with my interesting TG and CC-I will try to leave only the TX slot to on (no modify TG). Thank you for this fantastic forum! '73 Mario IU2MWK |
|
|
|
Post by Daniel VA2DG on Sept 16, 2020 0:19:59 GMT
HI Mario
i had same thing a month ago on my repeater, i could receive but BS on transmit. I reboot Pi-Star and it fix the problem.
Today i went out to the store and try my repeater with the mobile and could not transmit.
Dont know what is going on with Pi-Star
What version are you running at your end.?
|
|
dk5bm
New Member
Posts: 44
|
Post by dk5bm on Sept 16, 2020 7:02:37 GMT
I often have such a problem also with MMDVM/PI-Star based repeaters or hotspots, especially with the "new" boards. We have an "old" MMDVM based repeater with PI-Star, external modem on an Arduino board. This one runs perfect in combination with an old Kenwood TKR-850. My dual-hat-hotspot often don't want to hear my TYT or Kydera radios (BS timeout) while the Motorola DR3000 based repeater accept all radios everytime.
|
|
|
|
Post by Daniel VA2DG on Sept 16, 2020 11:20:53 GMT
My repeater has been running for years without problem and started this issue 6 months ago.
i re-tweak the audio 3 weeks ago and it was back on the air on RX. Last night i rebooted twice the Pi and does not accept my PTT with my TYT MD380, but same radio works ok on my 2 hotspots
|
|
IU2MWK
New Member
QUIS ULTRA ?
Posts: 10
|
Post by IU2MWK on Sept 16, 2020 15:51:35 GMT
Hi Daniel,the problem is the Pi-star-I suggest to perform "upgrade and update" in your pi star software,check the version of dashboard also (upper right)-When it worked you check the "BER" in the dashbord?
|
|
K6QYF
New Member
Posts: 29
|
Post by K6QYF on Sept 17, 2020 7:20:48 GMT
Firs i need to know if your channel/zone you are programming is for Repeater or here is a sample of my setup. Note that hotspot simplex is always TS2 and CC1 bot to work you have to put RX TS=off and TX TS=2 to work properly. Repeater is ok What if there is no "OFF" option for the RX TIME? All I have is Slot1....Slot2...and ON.....any idea's?? Thx |
|
IU2MWK
New Member
QUIS ULTRA ?
Posts: 10
|
Post by IU2MWK on Sept 17, 2020 10:18:03 GMT
Hi K6QYF,you have installed the new firmware version (last date 21th August),check the changelog : there's not option "OFF" but it's replaced by ON
The correct option are ON..Slot1 and Slot2-
Select the option ON (RX Time) if you have a channel in simplex mode.
|
|
K6QYF
New Member
Posts: 29
|
Post by K6QYF on Sept 17, 2020 14:08:04 GMT
Hi K6QYF,you have installed the new firmware version (last date 21th August),check the changelog : there's not option "OFF" but it's replaced by ON The correct option are ON..Slot1 and Slot2- Select the option ON (RX Time) if you have a channel in simplex mode. Okay...thank you for clarifying that. I do have the latest FWU and I run simplex on all my Digital channels...73 |
|
K6QYF
New Member
Posts: 29
|
Post by K6QYF on Sept 17, 2020 15:09:22 GMT
Hi K6QYF,you have installed the new firmware version (last date 21th August),check the changelog : there's not option "OFF" but it's replaced by ON The correct option are ON..Slot1 and Slot2- Select the option ON (RX Time) if you have a channel in simplex mode. Another question......on the "TX Policy".....should it be "Impolite" or "Polite to CC" ?...Thx |
|
IU2MWK
New Member
QUIS ULTRA ?
Posts: 10
|
Post by IU2MWK on Sept 18, 2020 19:14:51 GMT
In "TX Policy" I choose "Impolite"...only a frequency in simplex mode not work (164.625 Mhz) but i don't now why..
|
|
|
|
Post by oh8lrb on Nov 19, 2020 10:27:56 GMT
I also had this issue not RX. Somehow fixed it following advice and reading couple codeplug of members here and updated firmware, Thank You ! Interested nice small radio and enjoyable "stereo" audio by speaker microphone & speaker  ..newer know if some day the device might be compatible opengd... 73 Tomi / oh8lrb / oh4ms |
|
rd3x
New Member
Posts: 2
|
Post by rd3x on Nov 21, 2020 7:43:22 GMT
Hello everybody!
I have a problem like this:
In the DMR reception mode, I often stop hearing the reception.
I change the channel, audibility resumes.
This happens often.
Silence begins during the conversation of the correspondent.
If the channel is not ready, then the reception is restored at an undefined time.
This is not the case in analog mode.
|
|
|
|
Post by ea3bil on Dec 1, 2020 12:32:24 GMT
Hello everybody! I have a problem like this: In the DMR reception mode, I often stop hearing the reception. I change the channel, audibility resumes. This happens often. Silence begins during the conversation of the correspondent. If the channel is not ready, then the reception is restored at an undefined time. This is not the case in analog mode. We were suggested to TURN OFF TOT. It looks like helps, even not fixing the issue. |
|
eb3am
New Member
Posts: 6
|
Post by eb3am on Dec 1, 2020 18:55:49 GMT
If the display is put in "single" mode the reception is correct.
You need to go to Menu, localset, displaymode and activate S / D mode.
It not should, but at least it works.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Dec 9, 2020 12:20:26 GMT
|
|
