S52SX
New Member
Posts: 40
|
Post by S52SX on Aug 19, 2020 10:04:24 GMT
Hello, I'm experiencing a problems in CPS. When I'm programming a channels, I set everything proper and after I pressed button WRITE to send code plug to Kydera, CPS changed by it self a few parameters of channels. This is not normal. Please check attached pictures for better understanding. In second picture I have circled with yellow which parameters are changed by it selfs.   Does anyone have the same problems? The second issue I have experienced is that every time I sent code plug to Kydera, CPS again change my DMR ID to one number Higher than before. My ID is xxx0012, when I pressed write ID automatically goes to 13, and after that 14, 15,.. etc. Thanks and 73 DE Savo |
|
K6QYF
New Member
Posts: 29
|
Post by K6QYF on Aug 19, 2020 12:05:38 GMT
This happened to me as well....After I inputed all the code plug information....I would save it to a back up file and then open it back up and then write to the radio. As long as your getting the right information to the radio..that's what counts.
As far as your DMR ID changing....make sure that the (Rolling Code) box is (to the right)...is NOT checked...give that a try sir....73's
|
|
S52SX
New Member
Posts: 40
|
Post by S52SX on Aug 19, 2020 17:03:02 GMT
Hi,
Yes Rolling Code near by DMR ID was cheked and i have uncheked now and its OK . Thanks for this
Regarding SLOT changing, I have tried your way, but unfortunately doesn't helped. As soon as I pressed Save button, SLOTs changed to Off.
73
|
|
|
|
Post by 2e0ucw on Aug 19, 2020 20:32:33 GMT
I have the same issue. I wrote a code plug on CPS2.1 this afternoon - 4 zones - 2m FM simplex, 2m DMR simplex, 70cm FM simplex and 70CM DMR simplex.
I opened the code plug this evening to continue working on the code plug and I see that in zone 1, some channels appear that were in zone 2 - the rest of the channel data is correct.
I'm also experiancing the issue of the slots turning off - the rolling code solution does not work.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 19, 2020 22:45:26 GMT
Yes the CPS Programming Software is very flaky, I think we are all experiencing these problems, its a work in progress.
Anyone have the radio access specs so that it will be possible to produce 3rd party programming software?
Bruce
VK2RT
|
|
|
|
Post by Daniel VA2DG on Aug 20, 2020 3:42:11 GMT
Hi, Yes Rolling Code near by DMR ID was cheked and i have uncheked now and its OK . Thanks for this Regarding SLOT changing, I have tried your way, but unfortunately doesn't helped. As soon as I pressed Save button, SLOTs changed to Off. 73 HI can you tell me the CPS version , when open the CPS look at top left corner in the top bar and give me the 9.1.xxx number also go to your radio press Menu Device Info Version and give me the full date and time you see on the screen |
|
S52SX
New Member
Posts: 40
|
Post by S52SX on Aug 20, 2020 7:30:18 GMT
Hi Daniel
CPS version : 9.1.126
Device version : 109E.D4.EARSAB.004.F136-480 Aug 1 2020
|
|
|
|
Post by 2e0ucw on Aug 20, 2020 15:14:37 GMT
I'm using CPS 9.1.126
Device version : 109E.D4.EARSAB.004.F136-480 Aug 3 2020 21:49:50
|
|
S52SX
New Member
Posts: 40
|
Post by S52SX on Aug 21, 2020 6:56:17 GMT
Hello,
I need to report one more thing - PMR channels. I can put it in CPS, I can also save it and write it into radio, but If I chose this zone its empty. And also If I read my radio this zone is empty and If I check CPS its all changed back to original.
Another thing - If I choose empty zone, like PMR in my case radio stuck and only way to change zone is to write codeplug again to Kydera that boot up in first zone. The radio is normally operational now.
Also please add to new firmware ZONE name in display instead of number of zone
Also please add that boot up Zone can be chosen by me and not only first Zone
SCAN function - please add that I can choose time how log kydera will stay on channel even signal is gone, until it started to scan forward.
Thanks
|
|
S52SX
New Member
Posts: 40
|
Post by S52SX on Aug 22, 2020 7:55:21 GMT
Another BUG - I can add channels into 8 zones, as soon as I want to program channels in zone Nr. 9, CPS simply delete all channels in this zone. This happened also in Zone number 9, 10, 11... etc.
|
|
|
|
Post by Daniel VA2DG on Aug 23, 2020 3:17:49 GMT
Another BUG - I can add channels into 8 zones, as soon as I want to program channels in zone Nr. 9, CPS simply delete all channels in this zone. This happened also in Zone number 9, 10, 11... etc. Well i had 3 Zone and just added 10 more and program 4 ch ea new Zone , on Zone 13 i have one ch for my Hotspot on TG302233 and all work fine. Have a look at my CP. Dont Write to your radio because it is from the Beta FW So may it is fixed in the Beta Can you tell me what is your Firmware Date and TIme by checking in the radio Menu/Device INfo/ Version i will downgade to your VErsion and thry. Radio1-FW21Aug2020-13 Zone.F136 (229.04 KB) |
|
S52SX
New Member
Posts: 40
|
Post by S52SX on Aug 23, 2020 8:45:39 GMT
Another BUG - I can add channels into 8 zones, as soon as I want to program channels in zone Nr. 9, CPS simply delete all channels in this zone. This happened also in Zone number 9, 10, 11... etc. Well i had 3 Zone and just added 10 more and program 4 ch ea new Zone , on Zone 13 i have one ch for my Hotspot on TG302233 and all work fine. Have a look at my CP. Dont Write to your radio because it is from the Beta FW So may it is fixed in the Beta Can you tell me what is your Firmware Date and TIme by checking in the radio Menu/Device INfo/ Version i will downgade to your VErsion and thry. Hello Daniel, My firmware version is 109E.D4.EARSAB.004.F136-480 Date is Aug 1 2020 I have opened your test code plug, added a lot of channels in different zones, saved, reopened and it is working without deleting any of the channels. That really good job. Here is my test old codeplug who deleting channels : S52SX-23-08-2020-TEST-01.F136 (264.36 KB) Open it, test it and let me know. |
|
